20g Prometheus Bronze Clay
Prometheus® Jeweller’s Sterling White Bronze(PSW®) is a clay like material which turns into pure solid bronze, similar to silver colour when fired in a kiln. It is a mixture of micron-sized bronze powder, water and an organic binder. It can be formed by hand, rolled into a sheet or a rope. It can be moulded, textured, even turned on a potter's wheel. PSW® can be fired with most lab-created gemstones (cubic zirconias), pre-tested natural stones, glass beads, ceramic and porcelain.
When the clay is fired in a kiln, the organic binder evaporates and burns away and you’re left with pure, solid white bronze.
You can create unique jewellery, ornaments, hollow ware, statutes, sculptures and many other decorative objects. Anything you
create with PSW® is a piece of art.
You can perform multi-color pieces by combining PSW® with Prometheus® Bronze Clay(PBC®), Prometheus® Copper Clay(PCC®), Prometheus® Sunny Bronze Clay(PSB®).
Combine it with your imagination and let your fingers do the rest!
Working with PSW®
It is similar to working with Prometheus® Bronze Clay and Prometheus® Copper Clay silver clays, polymer clays, modelling
dough, flower dough and ceramic clays and very easy to use.
At normal consistency, PSW® does not stick to hands, working surface, instruments or molds without a need of any lubricating oils.
Remove the clay from its plastic bag and place it on a clean plastic surface or wax paper. Use your fingers, roller, spatulas, clay shapers, craft knives, tooth picks and other simple tools to shape it, texture it, or turn it on a potter’s wheel. You can texture the clay with rubber stamps, texture mats, leaves, paper, and other interesting textures. When you take with the clay out of the package, “The Wet Stage” begins. Try not to work at this stage for too long inorder to avoid your clay from drying out but, don’t rush your work, PSW® gives long long time to play with. However, if you detect any cracks on the surface, apply some water straight away with a brush or spray, and fill the cracks with a little paste to repair them.
To join two pieces together, simply wet the points that will touch, or add a little paste (to make a paste, simply mix a little clay with
a little water. If the two pieces are dry, wet the touching points, and paste to create a secure bond.
Store any unused clay in a plastic bag with a zipper to prevent it from drying out. Place any offcuts in the bag straight away whilst you
’re working, and keep it closed. If you’re not planning to work with the clay for a while, put the sealed plastic bag in a jar with
a tight lid. Placing a wet sponge to the bottom of the jar will keep your clay in a good condition, until your next usage. If you are storing it for a long time, keep an eye on the sponge and add water if needed.
Before firing the PSW®, you need to dry it completely. A hair dryer or putting it on top of a kiln will do it well. Hot-plates or food
dehydrators work well too. To check if the clay is completely dried, put the hot clay (straight from drying) on a cold mirror. After 10-20 seconds, move it and check that there is no condensation on the mirror. This test is especially important for big and thick pieces. If the piece is not dried completely, then it can crack, break or have bubbles on the surface while firing. We don’t recommend fast drying for a large piece, as it may cause cracks. For these, it is recommended to leave them at room temperature for a few hours and then continue drying at moderate temperatures.
Whilst the dried PSW®is strong, you still need to take some care when working with it. You can carve designs on the surface, file it, grind it, drill holes with hand tools or rotary tools and engravers. To join dried pieces, wet the joining points with a brush and apply some paste. After completing your design, it is easy to sand uneven surfaces, using sand papers, and sanding sponges. It is a lot easier to do this step now - before you have fired the clay!
This is a 2-step-method.
Put approximately 3 cm. of activated carbon to the bottom of a steel container. Place the pieces with at least 1.5 cm space between
in each other and point cold kiln or pre-heated kiln and fire for 15 minutes at 500°C. Take the steel container out,
put it on a fire proof surface.
Fill the container with activated carbon, close the lid and put it into the kiln at 770°C or 2 hours. When the firing is completed, either leave it to cool down in the kiln or, carefully take it out and leave it on a heat isolated surface untill it is cold enough to take your pieces out.
You can combine PSW® with PBC®, PCC®, PSB® and fire with the same firing schedule. Please note that at this firing schedule, shrinkage of PCC® is 9- 10%, PBC® 13% and PSW® 15-16%.
If your pieces are thin and long than we recommend you to anneal your pieces inorder to maintain high strength and malleability.
Heat your pieces at 565°C for 5 minutes and quinch in water.
Polish the piece with a burnisher, polishing papers, a thumbler or polishing motor with. Using polishing compounds can give extra
shine to your works.
* Please note that date on the back is production date - not best before.